stm32-baremetal

STM32 Bare-Metal (CMSIS, No HAL)

Purpose

Guide agents through a minimal STM32 bare-metal project using CMSIS device headers and startup code only — no STM32 HAL — covering clock setup, linker script integration, peripheral register access, and a reproducible build layout for STM32F/G/H/L families.

When to Use

• Starting STM32 firmware without Cube HAL dependency
• Porting vendor examples to register-level drivers
• Integrating with skills/baremetal/baremetal-startup and skills/embedded/linker-scripts
• Debugging clock or flash placement issues on STM32
• Teaching register-level STM32 before RTOS or Zephyr

Workflow

1. Minimal project layout

stm32-bare/
├── startup_stm32f407xx.s   # vector table + Reset_Handler
├── system_stm32f4xx.c      # SystemInit(), SystemCoreClockUpdate()
├── stm32f407xx.h           # CMSIS (from ST pack or copy)
├── linker.ld               # FLASH/RAM regions
├── main.c
└── Makefile

Use CMSIS-Core (core_cm4.h) and device header from ST CMSIS pack or open-source packs (e.g. stm32-cmsis-device-f4).

2. Clock configuration (RCC)

STM32 requires explicit HSE/HSI and PLL setup before high-speed peripherals:

/* system_stm32f4xx.c — simplified PLL from 8 MHz HSE */
void SystemInit(void)
{
    RCC->CR |= RCC_CR_HSEON;
    while (!(RCC->CR & RCC_CR_HSERDY)) {}

    RCC->PLLCFGR = RCC_PLLCFGR_PLLSRC_HSE | (8 << 0) | (336 << 6) | (0 << 16) | (7 << 24);
    RCC->CFGR   |= RCC_CFGR_PPRE1_DIV2 | RCC_CFGR_PPRE2_DIV1 | RCC_CFGR_HPRE_DIV1;
    RCC->CR     |= RCC_CR_PLLON;
    while (!(RCC->CR & RCC_CR_PLLRDY)) {}

    FLASH->ACR = FLASH_ACR_LATENCY_5WS;
    RCC->CFGR  |= RCC_CFGR_SW_PLL;
    while ((RCC->CFGR & RCC_CFGR_SWS) != RCC_CFGR_SWS_PLL) {}

    SystemCoreClockUpdate();
}

Always match FLASH_ACR wait states to voltage scale and SYSCLK per reference manual table.

3. Enable peripheral clock before MMIO

#define RCC_AHB1ENR_GPIOAEN (1U << 0)

static inline void gpioa_clock_enable(void)
{
    RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN;
    (void)RCC->AHB1ENR; /* AHB read-after-write — required on STM32 */
}

4. Build flags (arm-none-eabi-gcc)

MCU      = -mcpu=cortex-m4 -mthumb -mfpu=fpv4-sp-d16 -mfloat-abi=hard
CFLAGS   = $(MCU) -Wall -Wextra -ffunction-sections -fdata-sections -g3
LDFLAGS  = $(MCU) -T linker.ld -Wl,--gc-sections -specs=nano.specs -lc -lm -lnosys

5. Flash map (typical F4)

Region	Address	Notes
Flash	0x08000000	Vector table at boot
SRAM1	0x20000000	Stack, heap, .data/.bss
CCM	0x10000000	F4 only — not DMA-accessible from all masters

Bootloader apps often link at 0x08010000 and set SCB->VTOR = 0x08010000 on entry.

6. QEMU note

QEMU STM32 machines (stm32vldiscovery, netduinoplus2, etc.) use different MCUs than F407 and omit GPIO/DMA/I2C per QEMU STM32 docs. Use skills/qemu/qemu-embedded-simulation for simulation; validate F4 firmware on hardware.

7. Agent usage

/stm32-baremetal Scaffold CMSIS-only STM32F407 project with USART2 printf

Common Problems

Symptom	Cause	Fix
Hang in SystemInit	HSE not populated / wrong PLL	Use HSI for bring-up; verify crystal
Peripheral dead	RCC clock gate off	Enable AHB/APB bit; read-back RCC
HardFault on boot	Stack in wrong region / VTOR	Check _estack in linker.ld
Wrong baud rate	SystemCoreClock stale	Call SystemCoreClockUpdate() after PLL
DMA fails from CCM	CCM not on AHB matrix path	Place DMA buffers in SRAM1

Related Skills

• skills/baremetal/baremetal-startup — vector table and .data/.bss
• skills/baremetal/mmio-and-bit-manipulation — register access patterns
• skills/baremetal/bootloaders-embedded — app offset and VTOR relocation
• skills/embedded/linker-scripts — FLASH/RAM MEMORY blocks
• skills/embedded/openocd-jtag — flash and GDB via ST-Link